Posts on David P. Discher

Web Site exported to Hugo

Mon, 02 Nov 2026 04:50:34 +0000

Website exported to hugo

Exported my web site from wordpress to hugo static generator.

OM615 Kitchen Refresh Idea 2021

Wed, 20 Jan 2021 22:25:22 +0000

Idea for. two tone – with roll up door for “coffee” bar.

An idea I like for backsplash.

Awesome Idea for tones and how to slide the color into the frig box.

Also like this for backsplash.

MTCH101

Sun, 20 Dec 2020 22:51:13 +0000

MTCH101 – Single-Channel Proximity Detector Demo and Hookup

My values are a bit different – probably because I was out of 10Ks. These are all 5% standard resistors. Running 220 on the LED, because of the LED I’m using. Unclear in video what power supply I used, but when dusting this off in Dec 2020, I used a 5v @ 1amp USB Charger – which read ~5.2v without load.

The Proximity Sensor is just a wire here, and the type of wire, amount of insulation, length, affects all kinds of stuff.

Facebook Health Update Posts – 2020

Sat, 19 Dec 2020 23:23:20 +0000

March 25 – ER Trip for Back Pain
- https://www.facebook.com/daviddpd/posts/10157900210540874
March 27 – Rhomboid Muscle Spasm
- https://www.facebook.com/daviddpd/posts/10157908222820874
May 8 – Paralyiszed –
- https://www.facebook.com/daviddpd/posts/10158065256240874
May 13th – The Phantom back Pain
- https://www.facebook.com/daviddpd/posts/10158082573345874
May 14th –
- https://www.facebook.com/daviddpd/posts/10158083797505874
May 16th Hair Cut
- https://www.facebook.com/daviddpd/posts/10158090694915874
- https://www.facebook.com/daviddpd/posts/10158090915515874
May 24 – The Complication: Attack of Staphylococcus
- https://www.facebook.com/daviddpd/posts/10158115894090874
May 31 -RIP: Lucy • Oct 2004 ~ May 31, 2020
- https://www.facebook.com/daviddpd/posts/10158137278225874
May 31 – Pic line
- https://www.facebook.com/daviddpd/posts/10158137888315874
June 1
- https://www.facebook.com/daviddpd/posts/10158139886685874
- https://www.facebook.com/daviddpd/posts/10158140322095874
June 4: Four Weeks
- https://www.facebook.com/daviddpd/posts/10158149266570874
June 8th – WBC
- https://www.facebook.com/daviddpd/posts/10158161468210874
June 10th – WBC – Nadir’ed !
- https://www.facebook.com/daviddpd/posts/10158167077950874
June 11 – Stanford Hospital Breakfast
- https://www.facebook.com/daviddpd/posts/10158169466925874
- June 11 – Transport !
  - https://www.facebook.com/daviddpd/posts/10158169980890874
  - https://www.facebook.com/daviddpd/posts/10158170367295874
June 12 – Santa Clara Valley Medical Center – already pisses me off
- https://www.facebook.com/daviddpd/posts/10158172216560874
- https://www.facebook.com/daviddpd/posts/10158172465430874 (horrible food)
June 13 – Correct the record, but still …
- https://www.facebook.com/daviddpd/posts/10158175116865874
June 14 – Work from Rehab
- https://www.facebook.com/daviddpd/posts/10158178802885874
June 19 – IV issues
- https://www.facebook.com/daviddpd/posts/10158192886825874
- https://www.facebook.com/daviddpd/posts/10158193149980874 (hair loss)
June 24 – The Return Home
- https://www.facebook.com/daviddpd/posts/10158196008910874
June 25 – Reunited with my Angel
- https://www.facebook.com/daviddpd/posts/10158209949755874
June 29 – Pill board
- https://www.facebook.com/daviddpd/posts/10158223873425874
July 4th – Caturday with Angel
- https://www.facebook.com/daviddpd/posts/10158240722930874
July 5th – Selfie
- https://www.facebook.com/daviddpd/posts/10158243767125874
July 14 – Photo shoot with Angel
- https://www.facebook.com/daviddpd/posts/10158269357885874
July 15th – The Boring Musical Montage
- https://www.facebook.com/daviddpd/posts/10158272119265874
Aug 6 Wheelchair and coffee
- https://www.facebook.com/daviddpd/posts/10158328519700874
Aug 6 – Four Cycle of Chemo
- https://www.facebook.com/daviddpd/posts/10158328630930874
- https://www.facebook.com/daviddpd/posts/10158330287785874 (aug 7)
Aug 15 – Caturday with Angel
- https://www.facebook.com/daviddpd/posts/10158350385590874
Aug 17th – Angel is struggling
- https://www.facebook.com/daviddpd/posts/10158355673615874
Aug 19th – RIP: Angel – Nov 2002 – Aug 19, 2020
- https://www.facebook.com/daviddpd/posts/10158359500205874
Sept 10th – I can drive !
- https://www.facebook.com/daviddpd/posts/10158411016940874
Oct 3th – The Rise of DPD
- https://www.facebook.com/daviddpd/posts/10158464027470874
Oct 16 – Post chemo PET – No Cancer detected
- https://www.facebook.com/daviddpd/posts/10158490577660874
Dec 19 – Recovery Continues
- https://www.facebook.com/daviddpd/posts/10158630196955874

Fujitsu ScanSnap S1500M, macOS 10.15 Catalina & SANE

Sat, 11 Jan 2020 21:50:09 +0000

Fujitsu ScanSnap S1500M, macOS 10.15 Catalina & SANE

Fujitsu abandoned support for ScanSnap S1500M with MacOS 10.15 Catalina, but open Source SANE (Scanner Access Now Easy) allows it work on MacOS and Linux.

I’m finally taking the plunge, and slowly moving my 3 macs from 10.14 to 10.15. One issue was the ScanSnap S1500M. I search hi and low, read reviews and software support and bought the ScanSnap S1500M used on Amazon of $99 in January 2019. Unfortunately, I didn’t realized Fujitsu would be so lame as to end support. Yes, VueScan and ExactScan both support this scanner, and work well, but this is well over $100 of software for a $99 scanner.

Xen XCP-NG 8 PXELINUX CFG for Supermicro X9 SOL Serial Console on COM2

Sun, 15 Dec 2019 18:35:31 +0000

label xenserverCom2HVC
 MENU LABEL ^XCP-NG Installer COM2-HVC
 kernel mboot.c32
 append xcp-ng/xen.gz dom0_max_vcpus=2-4 dom0_mem=2048M,max:4096M com2=115200,8n1,0x2f8 console=com2 --- xcp-ng/vmlinuz xencons=ttyS1 console=hvc0 earlyprintk=xen nomodeset install --- xcp-ng/install.img

All the files above, including the PXELINUX .c32 are on the xcp-ng ISO image. (See /boot in the ISO Image).

Then copy the entire contents of the ISO to a an HTTP directory. On FreeBSD, I created mkdir -p /usr/local/www/apache24/data/xcp then copy sudo sh -c "tar -cf - . | tar -C /usr/local/www/apache24/data/xcp -xf - " … this then works with with the default configuration from www/apache24.

FreeBSD rc.conf to rc.conf.d one liner

Wed, 27 Nov 2019 23:17:36 +0000

cat rc.conf | awk -F _ '{print $1}' | sort | uniq | xargs -I % sudo sh -c "grep ^% rc.conf >> rc.conf.d/%"

Results may vary. Will handle basic SERVICE_* names …

MariaDB 10.4 – with Sysbench FreeBSD, Linux (CentOS) and ZFS

Fri, 15 Nov 2019 19:32:51 +0000

Software & Hardware Setup

Linux
- Linux 3.10.0-1062.1.1.el7.x86_64 #1 SMP Fri Sep 13 22:55:44 UTC 2019 x86_64 x86_64 x86_64 GNU/Linux
- CentOS Linux release 7.7.1908 (Core)
- kmod-zfs-0.8.2-1.el7.x86_64

FreeBSD

FreeBSD 12.1-STABLE FreeBSD 12.1-STABLE r354267 DPD amd64
- ( ~ 12.1-release, from 12-stable svn )

 <li>
 base zfs in 12.1
 </li>
 <li>
 openzfs-kmod-2019101600
 </li>
 <li>
 AVAGO MegaRAID SAS FreeBSD mrsas driver version: 07.709.04.00-fbsd
 </li>
</ul>

Hardware
- Intel(R) Xeon(R) CPU E5-2630 v3 @ 2.40GHz, Dual Sockets
- Supermicro X10DRH-CT
- 128GB RAM
- AVAGO/Broadcom 3108 MegaRAID (Integrated)
  - Firmware Package Build = 24.21.0-0028
  - Firmware Version = 4.680.00-8290
  - RAID50
  - Cache : Read Ahead Always, Always WriteBack, Direct
  - Stripe 1MB
  - 8 x MZILS480HCGR Samsung PM1633, 480GB TLC SAS 12Gbps

Testing Script

#!/bin/sh
os=`uname`


if [ "${os}" == "FreeBSD" ]; then
	TEST="/usr/local/share/sysbench/oltp_read_write.lua"
	SOCK="/tmp/mysql.sock"
else
	TEST="/usr/share/sysbench/oltp_read_write.lua"
	SOCK="/var/lib/mysql/mysql.sock"

fi

OPT1="--mysql-user=sysbench --mysql-password=abcd1234 --mysql-socket=${SOCK} --mysql-db=sysbench --tables=2 --table-size=500000000 --events=0"

sysbench ${TEST} --threads=8 ${OPT1} --time=600 --db-ps-mode=disable --report-interval=30 run
sysbench ${TEST} --threads=8 ${OPT1} --time=3600 --db-ps-mode=disable --report-interval=300 run

OPT2="--delete_inserts=2 --index_updates=2 --non_index_updates=0"

sysbench ${TEST} --threads=8 ${OPT1} ${OPT2} --time=600 --db-ps-mode=disable --report-interval=30 run
sysbench ${TEST} --threads=8 ${OPT1} ${OPT2} --time=3600 --db-ps-mode=disable --report-interval=300 run


OPT2="--delete_inserts=5 --index_updates=5 --non_index_updates=0"

sysbench ${TEST} --threads=8 ${OPT1} ${OPT2} --time=600 --db-ps-mode=disable --report-interval=30 run
sysbench ${TEST} --threads=8 ${OPT1} ${OPT2} --time=3600 --db-ps-mode=disable --report-interval=300 run

OPT2="--delete_inserts=10 --index_updates=10 --non_index_updates=1"

sysbench ${TEST} --threads=8 ${OPT1} ${OPT2} --time=600 --db-ps-mode=disable --report-interval=30 run
sysbench ${TEST} --threads=8 ${OPT1} ${OPT2} --time=3600 --db-ps-mode=disable --report-interval=300 run

Virtual Box, Disk Images, and EFI

Thu, 06 Jun 2019 20:44:51 +0000

To use it with VirtualBox we need to convert it to the VDI format:

VBoxManage convertdd sdb.raw sdb.vdi --format VDI

To use it with VMware we need to convert it to the VMDK format:

VBoxManage convertdd sdb.raw sdb.vmdk --format VMDK

VBoxManage modifyvm "VM name" --firmware efi

To switch back to using the BIOS:

VBoxManage modifyvm "VM name" --firmware bios

CentOS-RHEL-LVM – unfortunately

Thu, 06 Jun 2019 20:19:18 +0000

Import /active a volume group from a loop device.

vgscan
vgchange -ay vg0
mount /dev/vg0/root /mnt

FreeBSD – vm-bhyve config for CentOS 7.6 1810

Thu, 23 May 2019 18:51:03 +0000

CentOS 7.6 1810 – has released with a buggy EFI loader … which throws MokListRT error, even with bhyve UEFI booting. Here is the grub loader on how to to boot the CentOS 7.6 1810 DVD ISO.

loader="grub"
 grub_install0="linux /isolinux/vmlinuz LANG=en_US.UTF-8 KEYTABLE=us SYSFONT=latarcyrheb-sun16 console=ttyS0"
 grub_install1="initrd /isolinux/initrd.img"
 grub_run0="linux /vmlinuz-3.10.0-957.el7.x86_64 root=/dev/mapper/centos-root LANG=en_US.UTF-8 KEYTABLE=us SYSFONT=latarcyrheb-sun16 console=ttyS0"
 grub_run1="initrd /initramfs-3.10.0-957.el7.x86_64.img"

Psoriatic Arthritis: Return Of The Arthritic Pain

Fri, 03 May 2019 03:38:14 +0000

The pain is back.

So, I’m switching to Hurmia. In some minor miracle, insurance has approved all this within two days. I’ve had to wait till today, May 2nd for my first dose … which I got this morning. A nice part of this is that it is a self injectable, can be at room temperature for up to two weeks. It was also completely painless, I didn’t even feel the needle. Will see in two weeks when I need to do it myself, as this time was done with the nurse for as a “training” session. I’ve had some mild relief since, but might take longer for the full effectiveness.

Yet Another WordPress single install with multisite, Multitenancy configuration

Fri, 08 Mar 2019 20:33:30 +0000

OK. Yes, here we are again. The convenient evil of WordPress. I have multiple domains, and need multiple sites, that are pretty light on content. I run FreeBSD as the OS and have been doing system administration and large scale operations for a long time. In the past (early 2000’s) I had my own colo-ed servers, ran my own email, etc. I have since moved email to G-apps/G-suites and had my web sites hosted with the web hosting at my domain registrar. However, that site was raising prices, so I moved to a more basic registrar, and bought a t2.small reserve instance on AWS/EC2 – which was cheaper than the yearly subscription the shared web host offered at the registrar. Now, getting it to run with just a single installation of WordPress.

SysAdmin Notes: Enabling SSL Cluster replication – Let’s Encrypt – FreeBSD, MariaDB 10.2, and Galera Cluster

Tue, 06 Mar 2018 23:24:03 +0000

From acme.sh, you’ll get :

 ca.cer db2.cer db2.conf db2.csr db2.csr.conf db2.key fullchain.cer 

FreeBSD layout – copy these to /etc/ssl (well, where you want).

concatenate the ca.cer with symlink of cert.pem from the package “security/ca_root_nss”.

 sudo sh -c 'cat ca.cer cert.pem > cert2.pem' 

Galera Cluster doesn’t like chained certificates, and does both a client and server Certificate verification – so wsrep_provider_options look like this :

SysAdmin Notes: FreeBSD, MariaDB 10.2, and Galera Cluster

Mon, 06 Nov 2017 23:08:46 +0000

Intro

Installing and getting MariaDB 10.2, and Galera Cluster going on FreeBSD (from ports/packages) was not straight forward. The getting started were all geared for linux packages which seem to have different helpers. I couldn’t find any how to’s for freebsd.

These are more notes, not a how-to. Please, someone write up a better how-to or add in helper scripts to ports.

Packages / Ports

As things do and always change from version to version, custom poudriere builds, however all default options.
 galera-25.3.21_2 mariadb102-client-10.2.9_1 mariadb102-server-10.2.9_1 

A FreeBSD Router as an OpenVPN Client – Part 2: DNS Forwarding

Sat, 27 May 2017 14:29:58 +0000

So, I’m not sure why this didn’t work the first time, but got forwarding for just a single domain working in my unbound config for my vpn on my FreeBSD router.

It was seriously this simple:
 forward-zone: name: "ixsystems.com" forward-addr: 10.x.0.a forward-addr: 10.y.0.a forward-addr: 10.z.0.a 

A FreeBSD Router as an OpenVPN Client

Tue, 23 May 2017 15:46:20 +0000

Well, I’m back doing some work over at iX Systems, and really did not want to run Tunnelblick on my mac. The VPN for ix does do split tunnel/routing, however it pumps all the DNS over the tunnel … which makes accessing my local RFC 1918 NATed network hard to use.

I have Comcast Business Internet, and from all my research, Comcast Business Internet with Static IPv4, the modem cannot be made a raw/dumb bridge. A bridge mode modem, would release the statics. So I have modem, going into a pretty standard FreeBSD router/firewall setup, using NAT and ipfw. Yes, I like ipfw syntax better than pf. Whatever.

The War on Mother’s, Father’s, Christmas et al Days

Tue, 09 May 2017 14:09:09 +0000

In response to the following article, I was going to leave this as a comment to someone else posts, but decided to make this a personal post/rant in a more general area – are us lefties too politically correct ?

An open letter to pastors (A non-mom speaks about Mother’s Day)

Even though I am a man of 40 years old and child-less(*) man, luckily, I don’t believe in or practice any of these mythologies, so a hypocritical old child-less white man’s sanction or support from a conceived supreme being – is pretty meaningless for me.

Average Citizens AHCA Raw Bill Review – Part 1

Fri, 05 May 2017 21:53:48 +0000

So, What can an average, well-educated person get from reading the AHCA ?

Disclaimer, I’m a liberal, Sanders-Democrat living in Silicon Valley area of California. I’m currently enrolled in an individual plan, covered by the ACA, but NOT purchased via Covered California web site – but directly from the private insurance company. I am not a politician and have no legal education or background. I have an Engineering education and BS.

Anthem’s “Pathway PPO” Individual plan has physically injured me.

Fri, 10 Feb 2017 04:35:04 +0000

I have been a big proponent of the Affordable Care Act (ACA). The pre-existing conditions clause allowed me to take time off from my career and work towards re-training and building a startup. I’m writing documenting my experience not because of an issues with ACA, but because of a failure of a for-profit health insurance company interfering with my care.

I was diagnosed back in Spring of 2010 with psoriatic arthritis. I was plagued with mysterious pain in all different places, which I originally credited to soreness from snowboarding. It took months to correctly identify and determine what the best treatment was for me. Finally, I was prescribed REMICADE® (infliximab), and have been getting this every 7-8 weeks for 6 years. REMICADE is giving via intravenous infusion. ( I will refer to this as my “infusion” or “treatment”. ) During this time I was continuously employed and had been treated by the same medical group on various HMO/PPO plans and insurers from at least three different employers. Except for a small HMO vs PPO billing confusion (which took a year to resolve), all these insurance policies covered the same medical group for six years. This treatment has worked extremely well. Each infusion costs about $6,000-10,000 and I believe the cost of the drug has doubled in the past 6 years. (As well as the drug fluctuates in cost monthly.)

A Derby Photographer Notes

Sat, 05 Nov 2016 19:59:40 +0000

(Updated May 16, 2017)

I became an accidental derby photographer starting, I think November 8, 2013 – shortly after the Peninsula Roller Girls followed me on Twitter. Three years later, I’ve upgraded my camera body once, and added a second Canon 7D Mark II, Peak Design straps, a monopod, and a new camera bag but the same main lens – I learned a few things.

I often to forget some of these, so reviewing them before the shoot, may be helpful. (In theory – I’m gonna update this post from time to time.)

This is Personal: ACA, ObamaCare and the GOP

Wed, 26 Oct 2016 17:09:45 +0000

Friends and especially FAMILY – Your votes matters to my HEALTH.

This is extremely personal for me.

If you vote Republican, especially for ones that want to repeal the Affordable Care Act (ACA, “ObamaCare”) – you will hurt my health. (BTW – ObamaCare is NOT insurance, it is laws. Some states have not fully enacted the ACA due to partisanship and obstructionism.)

If you vote for candidates and support repealing the ACA, and currently have insurance via your employer, you have a misunderstanding. You are NOT using ObamaCare (except for things like children being able to stay on your plan till 26, covering preexisting conditions, free birth control and other zero cost preventive care). If you get insurance via your employer, and think the ACA is bad – then you don’t understand the complete scope of the law.

The Final Module for the chatFabric Device

Fri, 30 Sep 2016 20:50:28 +0000

Well, at least the final testing concept board for this yet-to-be-name product line, again made right here in Silicon Valley, CA at RushPCB. This is a ESP-12e/ESP8266 carrier board, with some of the external logic to glue everything together. Most of parts I’ve been able to source from Arrow Electronics. They have free shipping on everything right now – no promo code needed.

chatFabric dual (2) Relay Board

Wed, 21 Sep 2016 02:25:06 +0000

So the project continues with my 4th PCB, but my first PCB from RushPCB right here in Silicon Valley, CA.

I gained a few twitter followers from hobbyist to VCs to Tech Writers from the ESP8266 Community, Arrow Electronics, and RushPCB re-tweeting my Tweet when I got the board in, so I thought I’d write a bit long description and better pictures. But also being a bit egotistical, I thought I’d try to strike while the iron is hot … and see if there is enough interest in these. If so, I’d do a small run and sell them. (Unfortunately, in small qualities, it would likely be in the $8-10 range. I’d need to sell at least 1,000 to get that price down. The Songle board can be found for about $3. ) This small board is part of a whole IoT home automation platform and ecosystem of devices I’m working on, which hopefully will launch a few of them via crowdsourcing later this year.

Facebook, Flickr, and Lightroom, getting filenames and titles to sync

Mon, 16 May 2016 15:11:25 +0000

This past weekend, I shot almost 9,000 photos at Attack of the C Squads Roller Derby Tournament – Fantastic Four with four lenses and two bodies. I rented a second Canon EOS 7D Mark II from BorrowLenses, and learned a few tips and tools to make life easier.

First, make sure that your clocks are set correctly between the two camera bodies. I kept getting a warning when using the USB cable to connect the camera to my MacBook Pro about time-zone issue. The EOS utility will sync the clock to the computer. But I ignored this warning. In short, double check the clocks on the camera bodies before shooting.

The New McCarthyism

Sat, 28 Nov 2015 06:12:30 +0000

I am declaring, based on the bigoted and xenophobic responses to certain religions and peoples’ nationals origins, that we have entered an era of “New McCarthyism”

The New McCarthyism is the practice of vilifying people of a race, religion or national origin as terrorists without proper regard for evidence.

(I’m looking for a new name than “The New McCarthyism” – but nothing seems to work – open to suggestions.)

For reference, the the term was coined in the early 1950’s, named after Republican U.S. Senator Joseph McCarthy of Wisconsin:

Planned Parenthood and The GOP Hypocrisy: Lobbying and SuperPACs

Wed, 30 Sep 2015 04:47:49 +0000

I’m watching the CSPAN coverage of the Planned Parenthood Government Funding. It’s hilarious that the Republican Congressmen, especially the chair of this committee, attempting to use funding legal lobbying, legally funding of super PACs, and other political campaigns to prevent PlannedParenthood from receiving federal funds (note: mainly via Medicaid).

Remember, Oil/Energy companies – lobbying for Keystone XL, or defense companies – lobbying and funding super PACs, and Wall St, who got bailed out, lobby and support Super PACs. They got 100s of billions dollars. So, if you a fiscal conservative, and object to this … then just be constant. However, right now, this is just fine and legal. Citizens United baby!

Calling Out Someone’s Religious Beliefs

Sat, 19 Sep 2015 00:22:18 +0000

Again, President Obama is being called a non-America (apparently Hawaii isn’t part of the United States of America), and that he is a Muslim (or maybe more correctly believes in Islam, which is not his public statement of his religion).

As an American, with freedom of religion guaranteed to me, and every other American, I absolutely give Zero Fucks what religion Obama, Trump or anyone is associated with. One is also allowed the freedom to change their religious beliefs.

Propaganda vs Facts: “major abortion centered company”

Wed, 16 Sep 2015 23:19:13 +0000

So, I will have a lot more to say on this topic, but I want to make one point really quickly.

A “friend”, recently shared Alliance Defending Freedom’s video of a 10th undercover about Planned Parenthood. In a volley of exchange comments, the conversation (which I will link here, once redacted to protect the “friend”, more context below) – she made this statement:

[…] I’d love to stop funding a major abortion centered company.

Fact checking the News

Tue, 12 May 2015 22:36:20 +0000

So PunditFact published “Scorecards for the TV networks”, and how much one network “lies” got some social media traction today.

The comparisons are interesting, but be cautious about using them to draw broad conclusions. We use our news judgment to pick the facts we’re going to check, so we certainly don’t fact-check everything. (1)

Shouldn’t we fact check everything ? Isn’t it the responsibility of journalists to fact check everything ?

The conservative news website of the National Review, which I believe was trying to discredit PunditFact’s scorecards, had this to say:

Really Dumb Interview Questions

Fri, 08 May 2015 23:41:23 +0000

I’m really getting feed up with people asking me dumb questions. I’m not a recent college graduate and don’t have quick-sort memorized. I’m also not a search engineer. So I’m not going to be able to impress you with the algorithm I develop in 5 minutes during our face-to-face interview on a white board.

I was on an interview this afternoon, and I was asked by a Java developer … something along the lines:

Fifty Days of the 365

Wed, 25 Mar 2015 01:04:51 +0000

I didn’t tweet out the photos for the last several days, so lets look at the last 3 days of my 365.

(Large images and links below.)

So what is a 365 ?

Over on Yahoo! Answers the best answer describes a 365 as a “challenge of personal exploration” for a photographer or aspiring one. After some quick Googling, I still like this 6 year old answer is the best.

First Ever Casting Call

Thu, 29 Jan 2015 19:01:19 +0000

I am finally taking my photography hobby to to the next level, but I need a few models to help. I’m open to pretty much any type or look, from professional models and actors seeking head shots, to families, bands, or athletes who want to sit for me.

For this round, I am going to focus on three styles of studio portraits, each of which have three variations. All of these will be shot in front of black or white seamless backgrounds. This could include many different poses, with or without props, including multiple wardrobe changes.

Yet another tweak to flickr-share-with-attribution

Sun, 25 Jan 2015 21:47:41 +0000

So, a few bug fixes to my little utility that will hopefully finally allow me to push past my procrastination and create my casting call blog.

I moved to using iFrames. This is an attempt to be compatible with different themes. The CSS is also local to the iframe, so the flickr embedding should be persevered between themes. But, I haven’t actually tested that yet.

Of course, these charges are pushed up to my github repo : daviddpd/flickr-share-with-attribution.

wp flickr-share-with-attribution – Creative Commons and All-Rights Reserved

Sun, 07 Sep 2014 03:40:55 +0000

Well … I haven’t explained whole reason why I wrote this little utility, and well, not going to explain it now.

I’ve thinking about it and I still want to be able to link to “All Rights Reserved” images. I could probably embedded them anyway with the copyright notice, or contact each person and ask their permission. It just seems like a lot of work. For this use-case, I’m going to just link them.

Flickr-WordPress – I had to write it

Tue, 19 Aug 2014 04:58:47 +0000

So, after all the tinkering, I had to write it myself. I couldn’t get anything exactly right, so I wrote something with Flickr APIs to generate the HTML that I wanted, as well as following Creative Commons best practices for attribution. It’s just a stand-alone PHP CLI script, with hopes and desires to grow up to be a Word Press Plugin.

The code is up on github, flickr-share-with-attribution, under the 2-clause BSD license.

Trying to Find a Great Flickr Word Press Plugin

Mon, 18 Aug 2014 03:01:35 +0000

I might just have to write my own Word Press – Flickr plugin. There are SOOOO many, yet I have not found one that does what I’d like it to do. I would like to simply embed the photo with credit, title and the link back. And maybe the description too. I already know the photo ID, I don’t need discovery or search features, I just need the inserting. The flickr BBcode embed mark-up is almost what I want, and would be happy with. I’ve tried the BBcode plug-ins in Word Press, but it wasn’t clean enough.

Testing with Lucy

Thu, 03 Jul 2014 03:23:58 +0000

Playing around with wordpress plug-ins for flickr and twitter. Here’s a picture Lucy that I have on my business cards.

ALT-CONTROL-DELETE

Tue, 01 Jul 2014 19:56:10 +0000

Reset and reboot. Let’s get started.

I’ve wanted to start a blog for while, continuously having to put it off. What better day, than July 1st, the start of the 3rd quarter to kick off a blog. I do not have any firms plans for what will be here, however there are a lot of things in my head, and many different ways this could go.

Things will definitely change here – don’t really like the colors and theme yet, so it will change.